Replacing car number light bulbs

In order to change the number plate light on a car, you need to remember some of the rules. First of all, you can set yourself only the license plate light, which is located behind. For this, it is recommended to use LEDs with lenses, since they better illuminate the number and, according to the law, make it possible to more clearly see the license plate. Although lamps of various colors are commercially available, the law does not permit many of them to be put into practice.

Independent work for drivers

Replacing the number light bulbs in the following sequence:

With a thin screwdriver, it is necessary to disassemble the ceiling in half, starting from the middle.
Regular lamps are carefully unscrewed, since it is quite easy to damage the holder on the body.
The next step is the installation of LED or incandescent lamps.
Before installing in its place, the ceiling should be degreased.
After installing the lampshade, you should check the operation, if the replacement of the backlight for the back number was performed accurately, the number will be brightly lit.

When replacing the backlight on different car models, there are small nuances that differ during installation. For the work to be done correctly, such differences must be taken into account.

Conducting work with the Hyundai Solaris

The license plate is illuminated by two lights that are located on the trunk lid under the trim, they are interconnected. In order to replace the Hyundai-Solaris backlight, it is necessary to remove the trim from the trunk lid, for this:

Use a screwdriver to pry off the lid in the handle that locks the boot.
Despite the resistance provided by the clips, open the cover.
Using a Phillips screwdriver, unscrew both screws that secure the handle, remove it.
Using the same screwdriver, unscrew the caps that secure the trim in the trunk lid and remove them, after which the trim is removed.
It is necessary to turn the cartridge fully clockwise and, together with the lamp, take it out of the lamp housing, pull out the wires to such a length that it is convenient to change the lamp.
To remove the lamp from the cartridge, just pull it by the bulb.

In order for the replacement of the Hyundai Solaris backlight bulb to be performed correctly, the entire installation of lamps and parts must be carried out in the strictly reverse order.

After completion, it is necessary to check the assembled equipment. Subject to all conditions and requirements, the backlight should work without fail, only after that the replacement of the Solaris room backlight will be considered independently carried out qualitatively.

Substitution on "Prior"

It’s also not difficult to do such work on the Prior, just follow the instructions accurately and have the necessary tools. First of all, you need socket wrenches:

Using the keys, you need to remove the plastic, mounted on eight hedgehogs.
To remove the rear chrome frame above the number, you need to unscrew all four nuts. Lamps are installed in the frame.
In order to get the bulbs installed in the ceiling, you need to use a little effort, since they are difficult to disassemble.
When opening the lampshade, it is important not to lose the rubber bands. Replacing the backlight of the Priora number is quick.

It is imperative to check the operation of the installed bulbs before assembly, so that you do not have to engage in repeated work. The reassembly process occurs in the exact order with its disassembly. After replacing the lamps, shades are installed, then a frame is put in its place, which is fixed with bolts. After that, the removed plastic is put in its original place. At this, the replacement of the room backlight bulbs is considered complete.

The process of replacing Kalina

Over time, any vehicle requires replacement of worn parts, and Kalina is no exception. If the license plate has become poorly or unevenly lit, then the Kalina light will be replaced. It is easy to do it yourself:

For greater convenience, it is worth opening the trunk of the car, remove the ceiling.
To remove the lampshade with a thin screwdriver, you need to push it on the left side until it moves to the right and squeeze it on yourself.
Carefully, so as not to break, lifting the latch up, use a screwdriver to remove the flashlight.
Lift the plastic retainer up and remove the power plug.
After that we take out the base with the bulb, turning the white case counterclockwise.
We remove the bulb from the base, pulling it slightly to the side.
After replacing the lamp, all work is done in the reverse order.

Replacing the number light bulbs does not require special skills, you need attention, patience and the desire to produce it yourself. Many owners of Kalina often encounter this problem; its solution will not take much time and does not require the intervention of specialists.

Room lights on "Qashqai"

Replacing the Qashqai number backlight bulbs is not particularly different from this procedure in other cars, there are only small nuances that should be followed. First of all, before repairing you need to disconnect the negative cable from the battery. Next, you must perform the following actions:

Using a screwdriver, remove the rear license plate light. To do this, you need to lightly press it to the right and pull outward.
Carefully remove the lampshade cover.
Disconnect the connector.
To pull out the lamp, turn the cartridge counterclockwise.

After a simple procedure, a new bulb is put in and the assembly is carried out in the reverse order. After installing the negative cable in place, it is necessary to check the operation of the backlight number. Replacing the number light bulbs with your own hands will save not only time, but also money.

Self-repair at Renault Logan

Illumination of the rear number is necessary at night to determine the registration number of the vehicle. Therefore, when it breaks down, it is necessary to replace the room backlight bulbs, which is easy to produce on your own. For Renault-Logan, as well as for many other car models, incandescent and LED lamps are suitable. The former do not have great reliability and low energy consumption, but due to their low price they are in demand. The latter are very bright and use little energy, but their cost is much higher.

Replacing the number light on Renault Logan will not take much time:

It is necessary to disconnect the negative cable from the battery terminal.
Press the lock and remove the license plate light from the groove of the rear bumper.
Press retainer and remove flashlight diffuser.
Remove the lamp that does not have a base from the lamp.
Install a new lamp and reassemble all parts in reverse order.

Self-installation does not take much time and will help to quickly fix the breakdown.

Toyota Corolla backlight

If it is necessary to replace the backlighting of the rear number on the Corolla car, simple steps must be taken.

Press down on the tab and lower the lamp lens down to get easy access to the damaged lamp.
Then turn the bulb holder counterclockwise, and then remove it.
Then unscrew the screws that secure the license plate light and completely lower the lamp.
Next, remove the bulb holder, for this you need to turn it counterclockwise.
The last step is to remove the bulb from the cartridge.

When the Corolla backlight is replaced, the assembly is done in the reverse order. Such work can be done by each driver independently.

Backlight for rear room

According to the rules of the road at dusk, the rear number plate should be highlighted in yellow or white. This will not only help determine if necessary the number of the vehicle, but also shows its direction of movement. If the license plate is lit in blue or red or with bright LEDs, this can cause an emergency. Since at night, the perception of a driver moving behind can change.